Fisher Price Baby Gym 73739 User Manual

Infant Gym  
Toddler Driver  
Product Number: 73739  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Adult assembly is required.  
Tool required for assembly and battery installation:  
Phillips screwdriver (not included).  
Requires three "C" (LR14) alkaline batteries for operation (not included).  
Product features and decorations may vary from the pictures above.  
Disc  
 
Battery Installation  
Battery  
Compartment  
Door  
1.5V x 3  
“C” (LR14)  
Dashboard  
SHOWN ACTUAL SIZE  
Battery Safety Information  
• Batteries may leak fluids that can cause  
a chemical burn injury or ruin your toy.  
To avoid battery leakage:  
• Do not mix old and new batteries or  
batteries of different types: alkaline,  
standard (carbon-zinc) or rechargeable  
(nickel-cadmium).  
Back View  
• Locate the battery compartment door on  
the back of the dashboard.  
• Loosen the screws in the battery compart-  
ment door with a Phillips screwdriver.  
Remove the battery compartment door.  
• Insert batteries as indicated inside the  
battery compartment.  
• Insert three "C" (LR14) alkaline  
batteries, as indicated inside the battery  
compartment.  
• Remove batteries during long periods  
of non-use. Always remove exhausted  
batteries from the toy. Dispose of  
batteries safely. Do not dispose of  
batteries in a fire. The batteries may  
explode or leak.  
• Never short-circuit the battery terminals.  
• Use only batteries of the same or  
equivalent type, as recommended.  
• Close the battery compartment door  
and tighten the screws with a Phillips  
screwdriver. Do not over-tighten.  
Hint: When lights or sounds from this toy  
become faint or stop, it’s time for an adult  
to change the batteries!  
• Do not charge non-rechargeable  
batteries.  
• Remove rechargeable batteries from the  
toy before charging.  
• If removable, rechargeable batteries are  
used, they are only to be charged under  
adult supervision.  
3
 
Assembly  
Windshield  
1
4
Arm  
Base  
Bumper  
• Fit the tabs on the bottom of the  
windshield into the slots on the bumper.  
Hub  
• Push down on the windshield to "snap"  
it into place.  
2
3
8
#8 x 1 / " Washer Head Screw  
Shown Actual Size  
• Fit an arm to the hub on a base  
as shown.  
3
8
• Insert the #8 x 1 / " washer head screw  
Peg  
Kickplate  
Hole  
through the hole in the arm and into the  
base. Tighten the screw with a Phillips  
screwdriver. Do not over-tighten.  
• Position the kickplate so that the deco-  
rated side faces you.  
• Repeat this procedure to attach the  
other arm and base.  
• Fit one of the pegs on the bottom of the  
kickplate into one of the holes near the  
base of the bumper.  
• Bend the kickplate slightly to fit the  
other peg into the corresponding hole  
on the other end of the bumper.  
5
Bumper  
3
Assembly  
Base Ends  
• Insert the ends of each base into the  
square slots in the bumper assembly  
as shown.  
• Push the tabs on the kickplate into the  
slots on the windshield and "snap" the  
two together.  
4
 
Dashboard  
Bumper  
8
6
Bottom View  
Support  
Arms  
9
16  
#8 x 1 / " Screw  
Shown Actual Size  
• Fit the ends of the arms into the holes  
in the bottom of the dashboard.  
Turn the bumper over, so that the bottom  
is facing you.  
Dashboard  
• Be sure the screw holes in the base and  
9
bumper assembly are aligned.  
9
16  
• Insert four #8 x 1 / " screws through the  
holes in the bumper assembly and into  
the base. Tighten the screws with a  
Phillips screwdriver. Do not over-tighten.  
9
Screws  
7
16  
#8 x 1 / "Screw  
Visible  
Shown Actual Size  
• From the back of the dashboard, insert  
9
16  
four #8 x 1 / " screws through the  
holes in the dashboard and into the  
arms. Tighten the screws with a Phillips  
screwdriver. Do not over-tighten.  
10  
• Look into the two holes on each end of  
the bumper. If the screws were inserted  
properly in this step, they should be  
visible in the holes.  
• If the screws are not visible, remove the  
four screws. Repeat step 6 making sure  
the end of the base is fully inserted into  
the bumper assembly with no gaps  
between the two parts.  
Hangers  
Hint: You may feel some resistance.  
Press firmly.  
• Fit a ring into the hole in the mirror.  
• Clip a ring to each of the hangers.  
• Attach a ring or key to the ring or mirror.  
Hint: Adjust the height of these toys, as  
baby grows.  
5
 
Infant Gym  
To convert to Infant Gym mode, press the button on each support arm and, at the  
same time, lift the arch until it "clicks" into position.  
• Slide the mode switch to  
gym mode.  
• When your baby kicks the toy, turns the steering wheel or hits the dangling toys,  
your child hears a fun song and sees blinking lights and a spinning roller.  
• Slide the mode switch to  
long-play gym mode. Enjoy the same features as  
in gym mode but with longer music and lights.  
• Slide the mode switch to  
to turn the power off.  
Lift  
Lift  
Press  
Press  
Mode Switch  
Hint: If your child is not actively  
playing with this toy, it turns off  
automatically after a few minutes  
(sleep mode).  
Buttons  
Wheel  
Dangling  
Toys  
6
 
Toddler Driver  
To convert to Toddler Driver mode, press the button on each support arm and,  
at the same time, push the arch down until it "clicks" into position.  
• Slide the mode switch to  
driver mode.  
• When your toddler kicks the toy, turns the steering wheel or grabs the dangling  
toys, your child hears driving sound effects, a song and sees blinking lights and  
a spinning roller.  
• Slide the mode switch to  
to turn power off.  
Push  
Push  
Press  
Press  
Mode Switch  
Hint: If your child is not actively  
playing with this toy, it turns off  
automatically after a few minutes  
(sleep mode).  
Buttons  
Wheel  
Dangling  
Toys  
7
 
Care  
• Periodically check all screws and tighten as required. Periodically check plastic parts  
for cracks and broken pieces.  
• Wipe all parts of this toy with a clean cloth dampened with a mild soap and water  
solution. Do not immerse this toy.  
• This toy has no consumer serviceable parts. Do not take this toy apart.  
FCC Note  
(United States Only)  
Note: This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or tele-  
vision reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Consult the dealer or an experienced radio/TV technician for help.  
Note: Changes or modifications not expressly approved by the manufacturer  
responsible for compliance could void the user's authority to operate the equipment.  
Consumer Information  
Questions? We'd like to hear from you!  
Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST  
Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment,  
please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Relations,  
636 Girard Avenue, East Aurora, New York 14052.  
For other countries, outside the United States:  
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.  
Great Britain: telephone 01628 500302.  
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.  
Consumer Advisory Service 1300 135 312.  
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.  
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.  
Printed in China  
73739c-0920  
©2003 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
 

Edelbrock Automobile Parts TRX300EX User Manual
Edimax Technology Satellite TV System EA MARS User Manual
Eiki Projector LC SM3 User Manual
Eizo Computer Monitor L797 User Manual
ETI Sound Systems INC DJ Equipment LHEC20 User Manual
Fisher Price Motorized Toy Car 73690 User Manual
Fisher Price Video Game Furniture T6349 User Manual
FoodSaver Food Saver V2860 IUK User Manual
Fujitsu Microcassette Recorder MB89990 Series User Manual
Gaggenau Electric Grill VR 230 User Manual