U L T R A S E R I E S
IQ-PIP-LITE
he Crown® IQ-PIP-LITE is a PIP™ (Program-
mable Input Processor) input module for
T
PIP2™ compatible amplifiers.* It connects
the amplifier to a 100 Mb Ethernet network allow-
ing it to be remotely controlled and monitored via
System Architect or IQwic software.
Features
The IQ-PIP-LITE is a HiQnet or TCP/IQ series
component. This means it connects to a HiQNet
system or IQ Network via 100 Mb Ethernet. This
provides faster IQ communications than the previ-
ous current loop, IQ bus, connectivity method.
With HiQnet or TCP/IQ, a large (or small) system
can be interconnected using standard off-the-shelf
100 Mb Ethernet components (Switches, Network
Interface Card, and cables). The IQ-PIP-LITE can
also be connected to the same network used to
pass CobraNet™ audio.1
•
•
•
A Programmable Input Processor with
TCP/IQ and HiQnet (connects to an IQ
System or HiQnet system via 100 Mb
Ethernet)
•
•
Can be connected to the same network
used to pass CobraNet audio
Implements SmartAmp features: Input
compressors, multimode output limiters,
error reporting and load monitoring
Remote control and monitoring of
PIP2-compatible Crown amplifiers
and some PIP1-compatible Crown
amplifiers
•
•
AUX connector configurable for AUX input,
AUX output, or Listen Bus
Three Year, No-Fault, Fully Transferable
Warranty completely protects your invest-
ment and guarantees its specifications
Faster IQ communications than the
IQ bus
The audio path in the IQ-PIP-LITE is processed
totally in the analog domain without the inherent
noise induced by analog-to-digital conversions.
While DSP-type functions cannot be supported
with this type of architecture, the standard Smart-
Amp™ feature set is. These features include input
compressors, multimode output limiters, error
reporting and load monitoring.
**Important: Some of the first generation Com-
Tech Series and Macro-Reference amplifiers have
soldered 16-pin ribbon and 5-pin signal cable con-
nections, rather than the modular type. If you
find that your original Com-Tech Series or Macro-
Reference amplifier has the soldered type cable
connections, contact the Crown Technical Support
Group for installation instructions.
Ethernet link when lit and the presence of Ethernet
traffic when flashing. A green 100 MB indicator
(integrated in the network connector) indicates a
valid 100 Megabit connection.
Memory Backup: 4 Megabit nonvolatile FLASH
memory for backup of run-time settings, presets,
and program storage. Capable of 10,000 write
cycles.
Power Requirements: No external power is
required. 160 mA at +24 VDC and 50 mA at –24
VDC. When installed into a Crown PIP2 compatible
amplifier, the unit receives 24 VDC from the
amplifier.
The IQ-PIP-LITE requires System Architect Soft-
Using the IQ-PIP-LITE with the IQ-PIP-USP2
Adapter
***Important: Some newer MA-5000VZ amplifiers
are already PIP2-compatible and can accept the
IQ-PIP-LITE directly. Older MA-5000VZ amplifiers
are not PIP2-compatible. Those amplifiers have
soldered 16-pin ribbon and 5-pin signal connec-
tions, rather than the modular type. If you find that
your MA-5000VZ amplifier has the soldered type
cable connections, contact the Crown Technical
Support Group for installation instructions.
The IQ-PIP-USP2 Adapter allows many older
Crown PIP-compatible amplifiers (i.e., Macro-
Tech® 00 Series, Com-Tech 00 Series, and Studio
Reference Series amplifiers) to access the power
and versatility of the Crown IQ-PIP-LITE module.
Total Power Dissipation: 4.6 watts.
Audio
The IQ-PIP-USP2 Adapter can be installed into the
following Crown amplifier models:
Please note: The audio specifications are refer-
enced to 0.775 V (0 dBu). Measurements were
made at the output of the IQ-PIP-LITE module
itself.
Important: The IQ-PIP-USP2 Adapter is designed
for use with the IQ-PIP-USP2 module and IQ-PIP-
LITE ONLY, and will NOT work with the IQ-PIP-
USP2/CN or any other PIP module.
CT-200**, CT-400**, CT-800**, CT-1600**
MA-600, MA-1200, MA-2400
MA-3600VZ, MA-5000VZ***
MA-24x6, MA-36x12
Macro Reference**
Studio Reference I
Input Impedance: Normally 20 kilohms balanced
and 10 kilohms unbalanced.
Maximum Input Level: +20 dBu.
Dynamic Range: >110 dB (A-weighted, 20 Hz to
20 kHz).
Frequency Response: 0.5 dB from 20 Hz to 20
kHz.
Common Mode Rejection (CMR): 50 dB typi-
cal.
Specifications
General
Connectors: See Figure 1 on other side.
Network: RJ-45 connector forming an IEEE 802.3
Ethernet NIC connection.
Studio Reference II
For more details about the IQ-PIP-LITE, contact
the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
AUX: RJ-11.
*A PIP2™-compatible amplifier is necessary to
use the IQ-PIP-LITE. To determine if the amplifier
Channel 1 and Channel 2 balanced inputs: 3-pin,
5mm removable barrier blocks.
Total Harmonic Distortion + Noise (THD+N):
< 0.05% (1 kHz, 0 dBu).
is PIP2 compatible, look for the
logo on
Indicators: A yellow DATA indicator flashes when
the IQ-PIP-LITE receives a valid command that is
addressed to the IQ-PIP-LITE. A green PRESET
indicator flashes to indicate the selected and active
user preset. A yellow LINK ACT indicator (inte-
grated in the network connector) indicates a valid
the back of the amplifier. The IQ-PIP-LITE is NOT
compatible with older Crown PIP amplifiers unless
a USP2 adapter is first installed in the amplifier.
Data Acquisition: Eight channel, 12 bit Analog
to Digital Converter running at 100 K samples
per second.
1 Note that the IQ-PIP-LITE cannot receive or
transmit CobraNet audio. Plese use the IQ-PIP-
USP3/CN if this function is desired.
Input/Output Monitor Accuracy: Typically 1 dB.
|
Conair Refrigerator 025 to 15 ton User Manual
Corega Headphones BTHS02 User Manual
Craftsman Tiller 91729604 User Manual
Cuisinart Blender CSB 77C User Manual
Cuisinart Mixer SM 55 User Manual
Dyson Vacuum Cleaner DC39 User Manual
Eaton Electrical Switch TRS 3064 User Manual
Fisher Paykel Washer 517735 User Manual
Gardena Yard Vacuum GS 1500 Art 2575 User Manual
GE Washer Dryer DBXR453ET User Manual